U-Boot 2010.06 (Apr 28 2015 - 09:46:30) Check spi flash controller v350... Found Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80 Spi(cs1): Block:64KB Chip:16MB Name:"S25FL129P1" MMC: MMC FLASH INIT: No card on slot! In: serial Out: serial Err: serial No mmc storage device found! Hit any key to stop autoboot: 1  0 16384 KiB hi_sfc at 0:0 is now current device cramfs load file : /boot/hikernel ### CRAMFS load complete: 2409600 bytes loaded to 0x82000000 ## Booting kernel from Legacy Image at 82000000 ... Image Name: hilinux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2409536 Bytes = 2.3 MiB Load Address: 80008000 Entry Point: 80008000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 3.0.8 (harvey@localhost.localdomain) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #2 Thu Apr 16 10:08:52 CST 2015 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: hi3518 Memory policy: ECC disabled, Data cache writeback AXI bus clock 200000000. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9144 Kernel command line: mem=36M console=ttyAMA0,115200 root=1f02 rootfstype=cramfs mtdparts=hi_sfc:256K(boot),768K(config),4608K(rootfs),10752K(app) PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 36MB = 36MB total Memory: 31940k/31940k available, 4924k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xc2800000 - 0xfe000000 ( 952 MB) lowmem : 0xc0000000 - 0xc2400000 ( 36 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0028000 ( 128 kB) .text : 0xc0028000 - 0xc0436000 (4152 kB) .data : 0xc0436000 - 0xc0458840 ( 139 kB) .bss : 0xc0458864 - 0xc0470cc8 ( 98 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:32 nr_irqs:32 32 sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms Console: colour dummy device 80x30 Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized NET: Registered protocol family 16 Serial: AMBA PL011 UART driver uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2 console [ttyAMA0] enabled uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource timer1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.16) msgmni has been set to 62 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered brd: module loaded loop: module loaded Spi id table Version 1.22 Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80 SPI FLASH start_up_mode is 3 Bytes Spi(cs1): Block:64KB Chip:16MB Name:"S25FL129P1" spi size: 16MB chip num: 1 4 cmdlinepart partitions found on MTD device hi_sfc Creating 4 MTD partitions on "hi_sfc": 0x000000000000-0x000000040000 : "boot" 0x000000040000-0x000000100000 : "config" 0x000000100000-0x000000580000 : "rootfs" 0x000000580000-0x000001000000 : "app" Special nand id table Version 1.35 Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10 Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 No NAND device found. Fixed MDIO Bus: probed himii: probed PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver hiusb-ehci hiusb-ehci.0: HIUSB EHCI hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1 hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000 hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver hiusb-ohci hiusb-ohci.0: HIUSB OHCI hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2 hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm usbcore: registered new interface driver uas Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver mdc800 mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 NET: Registered protocol family 17 NET: Registered protocol family 15 lib80211: common routines for IEEE802.11 drivers Registering the dns_resolver key type registered taskstats version 1 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) øVFS: Mounted root (cramfs filesystem) readonly on device 31:2. devtmpfs: mounted Freeing init memory: 128K usb 1-1: new high speed USB device number 2 using hiusb-ehci _ _ _ _ _ _ _ _ _ _ _ _ \ _ _ _ _ _ ___ / /__/ \ |_/ / __ / - _ ___ / / / / / / _ _ _ _/ / / \_/ \_ ______ ___________\___\__________________ [RCS]: /etc/init.d/S00devs mknod: /dev/console: File exists mknod: /dev/ttyAMA0: File exists mknod: /dev/ttyAMA1: File exists mknod: /dev/null: File exists [RCS]: /etc/init.d/S01udev udevd (557): /proc/557/oom_adj is deprecated, please use /proc/557/oom_score_adj instead. [RCS]: /etc/init.d/S80network mount app successful! Auto login as root ... Jan 1 00:00:03 login[568]: root login on 'ttyS000' Welcome to HiLinux. None of nfsroot found in cmdline. # cfg80211: Calling CRDA to update world regulatory domain RTL871X: module init start RTL871X: rtl8188eu v4.3.0.8_13968.20150417 RTL871X: build time: Jun 20 2015 15:24:38 RTL871X: usb_endpoint_descriptor(0): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=81 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_in = 1 RTL871X: usb_endpoint_descriptor(1): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=2 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_out = 2 RTL871X: usb_endpoint_descriptor(2): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=3 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_out = 3 RTL871X: nr_endpoint=3, in_num=1, out_num=2 RTL871X: USB_SPEED_HIGH RTL871X: CHIP TYPE: RTL8188E RTL871X: register rtw_netdev_ops to netdev_ops RTL871X: Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0) RTL871X: RF_Type is 3!! RTL871X: _ConfigNormalChipOutEP_8188E OutEpQueueSel(0x05), OutEpNumber(2) RTL871X: EEPROM type is E-FUSE RTL871X: ====> _ReadAdapterInfo8188EU RTL871X: Boot from EFUSE, Autoload OK ! RTL871X: SetHwReg8188EU: bMacPwrCtrlOn=1 bFWReady == _FALSE call reset 8051... RTL871X: =====> _8051Reset88E(): 8051 reset success . RTL871X: efuse_read_phymap_from_txpktbuf bcnhead:0 RTL871X: efuse_read_phymap_from_txpktbuf len:111, lenbak:111, aaa:111, aaabak:111 RTL871X: efuse_read_phymap_from_txpktbuf read count:109 RTL871X: EEPROM ID=0x8129 RTL871X: VID = 0x0BDA, PID = 0x8179 RTL871X: Customer ID: 0x00, SubCustomer ID: 0xCD RTL871X: Hal_ReadPowerSavingMode88E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1) RTL871X: ### PS params=> power_mgnt(0),usbss_enable(0) ### RTL871X: ======= Path 0, Channel 1 ======= RTL871X: Index24G_CCK_Base[0][1] = 0x2a RTL871X: Index24G_BW40_Base[0][1] = 0x2c RTL871X: ======= Path 0, Channel 2 ======= RTL871X: Index24G_CCK_Base[0][2] = 0x2a RTL871X: Index24G_BW40_Base[0][2] = 0x2c RTL871X: ======= Path 0, Channel 3 ======= RTL871X: Index24G_CCK_Base[0][3] = 0x2a RTL871X: Index24G_BW40_Base[0][3] = 0x2c RTL871X: ======= Path 0, Channel 4 ======= RTL871X: Index24G_CCK_Base[0][4] = 0x2a RTL871X: Index24G_BW40_Base[0][4] = 0x2c RTL871X: ======= Path 0, Channel 5 ======= RTL871X: Index24G_CCK_Base[0][5] = 0x2a RTL871X: Index24G_BW40_Base[0][5] = 0x2c RTL871X: ======= Path 0, Channel 6 ======= RTL871X: Index24G_CCK_Base[0][6] = 0x2a RTL871X: Index24G_BW40_Base[0][6] = 0x2c RTL871X: ======= Path 0, Channel 7 ======= RTL871X: Index24G_CCK_Base[0][7] = 0x2a RTL871X: Index24G_BW40_Base[0][7] = 0x2c RTL871X: ======= Path 0, Channel 8 ======= RTL871X: Index24G_CCK_Base[0][8] = 0x2a RTL871X: Index24G_BW40_Base[0][8] = 0x2c RTL871X: ======= Path 0, Channel 9 ======= RTL871X: Index24G_CCK_Base[0][9] = 0x2a RTL871X: Index24G_BW40_Base[0][9] = 0x2c RTL871X: ======= Path 0, Channel 10 ======= RTL871X: Index24G_CCK_Base[0][10] = 0x2a RTL871X: Index24G_BW40_Base[0][10] = 0x2c RTL871X: ======= Path 0, Channel 11 ======= RTL871X: Index24G_CCK_Base[0][11] = 0x2a RTL871X: Index24G_BW40_Base[0][11] = 0x2c RTL871X: ======= Path 0, Channel 12 ======= RTL871X: Index24G_CCK_Base[0][12] = 0x29 RTL871X: Index24G_BW40_Base[0][12] = 0x2b RTL871X: ======= Path 0, Channel 13 ======= RTL871X: Index24G_CCK_Base[0][13] = 0x29 RTL871X: Index24G_BW40_Base[0][13] = 0x2b RTL871X: ======= Path 0, Channel 14 ======= RTL871X: Index24G_CCK_Base[0][14] = 0x29 RTL871X: Index24G_BW40_Base[0][14] = 0x2b RTL871X: ======= TxCount 0 ======= RTL871X: CCK_24G_Diff[0][0]= 0 RTL871X: OFDM_24G_Diff[0][0]= 0 RTL871X: BW20_24G_Diff[0][0]= -2 RTL871X: BW40_24G_Diff[0][0]= 0 RTL871X: EEPROMRegulatory = 0x0 RTL871X: mlmepriv.ChannelPlan = 0x20 RTL871X: CrystalCap: 0x26 RTL871X: EEPROM Customer ID: 0x 0 RTL871X: EEPROM : AntDivCfg = 0, TRxAntDivType = 3 RTL871X: Board Type: 0x 0 RTL871X: ThermalMeter = 0x1a RTL871X: <==== _ReadAdapterInfo8188EU in 330 ms RTL871X: init_channel_set ChannelPlan ID 20 Chan num:13 RTL871X: rtw_macaddr_cfg MAC Address = 8c:18:d9:83:7b:79 RTL871X: bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 RTL871X: rtw_ndev_init(wlan0) RTL871X: _rtw_drv_register_netdev, MAC Address (if1) = 8c:18:d9:83:7b:79 usbcore: registered new interface driver rtl8188eu RTL871X: module init ret=0 Hisilicon Media Memory Zone Manager hi3518_base: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Hisilicon UMAP device driver interface: v3.00 pa:82400000, va:c2bc0000 load sys.ko for Hi3518...OK! load viu.ko for Hi3518...OK! ISP Mod init! load vpss.ko ....OK! load vou.ko ....OK! load venc.ko for Hi3518...OK! load group.ko for Hi3518...OK! load chnl.ko for Hi3518...OK! load h264e.ko for Hi3518...OK! load jpege.ko for Hi3518...OK! load rc.ko for Hi3518...OK! load region.ko ....OK! load vda.ko ....OK! regvalue = 68 GPIO regvalue = 64 gpio driver init successful! insmod: can't insert 'extdrv/hi_adc.ko': No such file or directory hi_i2c init is ok! Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 1, nodeamon= 0) Kernel: ssp initial ok! acodec inited! insert audio ==== Your input Sensor type is soih22 ==== OSPQueueCreate=====keyID:65537 OSPQueueCreate=====udwTempID:0 message OSPQueueCreate QuenceMsgID:0 .......... wait for receive message.......... cur process id : 795 open gpio_motor erro! parameter size is : 52476 LoadParameterFrom /var/config.dvr /home/harvey/src/app/3518/3518e/appe8188/appeCloud/parameter/parametermanage.cpp 2283 CheckExtendApSettings...... /home/harvey/src/app/3518/3518e/appe8188/appeCloud/parameter/parametermanage.cpp 2301 CheckWebSettings...... upnp port =22513 22514 22515 6 8c:18:d9:83:7b:79 deviceid = ZMD00ID02207254 InitDeviceConfigInfo :3 ---------read configinfo-------- UbootVersion:V7.0.0.0 KernelVersion:V7.0.0.0 RootfsVersion:V7.0.0.0 AppVersion:V7.4.0.9 DeviceName:ZM-SH75D001-WA HardWareVersion:799990304 SupportInfo:0000011d Channel:1 ------------------------------------- open rtc ds1307dev device failed! open rtc pcf8563dev device failed! Open misc rtc file failure! get time failed! loadTm ---------- year = 0,mon = 1074977184,date = 0,hour = 0,min = 203404,sec = 268435456 week 0 realtime---------- = 0,mon = 160,date = 0,hour = 0,min = 140,sec = 0 set sys date success MPP Version HI_VERSION=Hi3518_MPP_V1.0.8.1 sensor list num 4 ov9712 idl = 0x22 idh = 0xa0 sensor_list id = 0xa022 , ID = 0x9711 JXH22 idl = 0x22 idh = 0xa0 sensor_list id = 0xa022 , ID = 0xa022 sensor id ############################:1 ViDev:0 enIntfMode:2 enWorkMode:0 au32CompMask0:ffc00000 au32CompMask1 00000000 enScanMode:1 s32AdChnId0:-1 s32AdChnId1:-1 s32AdChnId2:-1 s32AdChnId3-1 enDataSeq:2 enDataPath:1 enInputDataType:1 @@@@@@@@@@@@stAEAttr.u16ExpTimeMax :: ffff @@@@@@@@@@@@stAEAttr.u16ExpTimeMin :: 2 @@@@@@@@@@@@stAEAttr.u16AGainMax :: 3 @@@@@@@@@@@@stAEAttr.u8ExpStep :: 80 @@@@@@@@@@@@stAEAttr.s16ExpTolerance :: 28 @@@@@@@@@@@@stAEAttr.enFrameEndUpdateMode :: 2 @@@@@@@@@@@@stAEAttr.u8ExpCompensation :: 70 =============before HI_MPI_ISP_GetAEAttrEx:1000 =============after HI_MPI_ISP_GetAEAttrEx:0800 stGammaAttr.enGammaCurve = 0 =====================AWBAttr.u8Speed :80 =====================AWBAttr.u8Speed :c8 ###########Antiflicker.bEnable :: 0 ###########Antiflicker.u8Frequency :: 0 ###########Antiflicker.enMode :: 0 ####2######Antiflicker.bEnable :: 1 ####2######Antiflicker.u8Frequency :: 60 ####2######Antiflicker.enMode :: 1 ########################## u32LumaVal:50 ,u32ContrVal:50,u32SatuVal:50 -------------------------AudioOutPutOnOff flag:0 InitAudio: InitAudioInitAudio,/dev/acodec =============== m_initAbnormalVoice:1 SetInPutVolume :28 SetOutPutVolume :31 Ai(0,0) bind to AencChn:0 ok! function: AudioEncodecThread threadid 1109468352 ,line:36 function: PlayFileThead threadid 1118459072 ,line:28 StartAudioDecode Success File size = 261702 --------------------------- resolution:0 framerate:20 VbrOrCbr:0 bitrate:1024 gop:40 --------------------------- StartVideoEncoder 0 thread success! --------------------------- resolution:2 framerate:12 VbrOrCbr:0 bitrate:320 gop:24 --------------------------- StartVideoEncoder 2 thread success! ================ CreateSnapChn:65 start!!! function: MDThreadEntry threadid 1135695040 ,line:245 MDThreadBody TID:1135695040 !!!! function: VideoEncoderThreadEntry threadid 1149400256 ,line:81 GetAVStreamInOneChn Start!! venc:0 function: VideoEncoderThreadEntry threadid 1157788864 ,line:81 GetAVStreamInOneChn Start!! venc:2 ================ CreateSnapChn:120 success =============stop osd show ! **************************************************************** * IPC zmdnetlib build version: [V1.6.1]  * IPC zmdnetlib build time: [10:38:22] [Jul 14 2015]  **************************************************************** *************************************************************************** * wifi for AR9271,MT7601,RTL8188,Internal Version:v1.0 Build Time:18:04:36,Jul 31 2015 * *************************************************************************** function: OsdShowEntry threadid 1166177472 ,line:14 OsdProcess pid:1166177472 !!!! RTL871X: +871x_drv - drv_open, bup=0 RTL871X: Set RF Chip ID to RF_6052 and RF type to 1T1R. RTL871X: rtl8188e_FirmwareDownload fw:NIC, size: 13904 RTL871X: rtl8188e_FirmwareDownload: fw_ver=b fw_subver=0001 sig=0x88e1, Month=11, Date=27, Hour=30, Minute=36 RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00030005 RTL871X: =====> _8051Reset88E(): 8051 reset success . RTL871X: _FWFreeToGo: Polling FW ready OK! (1, 10ms), REG_MCUFWDL:0x000300c6 RTL871X: FWDL success. write_fw:1, 90ms ==> rtl8188e_iol_efuse_patch RTL871X: pDM_Odm TxPowerTrackControl = 1 RTL871X: rtl8188eu_hal_init in 1190ms RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: MAC Address = 8c:18:d9:83:7b:79 RTL871X: -871x_drv - drv_open, bup=1 ADDRCONF(NETDEV_UP): wlan0: link is not ready RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =30---------- ##### QR_Scan_Thread success -----------------------------------GetConnectStatus:0 -----------------------------------GetConnectStatus:0 ########WifiLedProcess_Thread##### led_fd=31 OSPQueueCreate=====keyID:65537 OSPQueueCreate=====udwTempID:0 ========================= OSPQueueCreate Success m_QuenceMsgID:0 ----------------night frame:20 sendto: Network is unreachable -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 device wlan0 entered promiscuous mode -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(38) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(2d) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 sendto: Network is unreachable -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(30) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(44) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(38) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 sendto: Network is unreachable -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 RTL871X: survey done event(36) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 ---------------------------------RTL871X: set_mode = IW_MODE_MONITOR --GetConnectStatus:2 RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 ----------------day -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 Failed to get password !!! ----------------night frame:20 -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 stride: 1280,1280 RTL871X: survey done event(3f) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 4 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=4 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 sendto: Network is unreachable qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: Failed to get password !!! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 -------------platform_wifi_smartlink_cleanup 862----------------- stride: 1280,1280 RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 RTL871X: set bssid:00:00:00:00:00:00 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- RTL871X: survey done event(34) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 stride: 1280,1280 ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 Failed to get password !!! -------------platform_wifi_smartlink_cleanup 862----------------- RTL871X: set_mode = IW_MODE_INFRA RTL871X: hw_var_set_opmode()-4042 mode = 2 qrcode centers is: 0 ret:0,-------result: RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! RTL871X: set_mode = IW_MODE_INFRA RTL871X: set bssid:00:00:00:00:00:00 RTL871X: hw_var_set_opmode()-4042 mode = 2 ioctl[SIOCSIWAP]: Operation not permitted RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 RetartWPA:/app/wifi/tools/wpa_supplicant -B -Dwext -iwlan0 -c /config/wpa_supplicant.conf ------wpa_ctrl_open 1526 jam want to know socket id =40---------- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 stride: 1280,1280 RTL871X: survey done event(40) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) ###### LoginWifiDev.AuthenticationMode = 0 ###### LoginWifiDev.lang = 0 ###### LoginWifiDev.ConnectStatus = 0 ###### LoginWifiDev.EncryptionProtocol = 6 ###### LoginWifiDev.Index = 0 ###### LoginWifiDev.m_Reserved = 1 ###### LoginWifiDev.Passwd = ###### LoginWifiDev.RouteDeviceName = ###### LoginWifiDev.SignalLevel = 0 ###### LoginWifiDev.WepKeyMode = 0 Save Parameter ZMD_Connect_Wifi=====FUNC:ZMD_SmartLinkProcess,LINE:1877 Encryp=6 ssid= pwd= -----ssid is NULL ZMD_Connect_Wifi 1970------- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:4 -----------------------------------GetConnectStatus:4 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 RTL871X: set_mode = IW_MODE_MONITOR RTL871X: rtw_pm_set_ips IPS_NONE ---create monitor mode success----- qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:2 -----------------------------------GetConnectStatus:2 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------GetConnectStatus:11 stride: 1280,1280 qrcode centers is: 0 ret:0,-------result: -----------------------------------GetConnectStatus:11 -----------------------------------Get